Home > Amd Phenom > AMD Phenom II X6 1075 HyperTransport Causing BSODs?

AMD Phenom II X6 1075 HyperTransport Causing BSODs?

Benefit: Helps users get more efficient performance by dynamically activating or turning off parts of the processor. Note that these are calculated speeds, and should not be taken to word. Also, windows freezes along with the BSODs saying that a video driver went out but was recovered, I just installed the latest video drivers. Join our site today to ask your question. Check This Out

With the Phenom II, a new era of overclocking was created. Are you ready to learn how to unleash the beast? Terminology: CPU = Central Processing Unit NB = Northbridge CPU-NB = CPU – Northbridge (redundant I know) HTT = Hyper Transport HT or HTL = Hyper Transport Link (do not confuse Use for 12+ hours to learn if settings are fully stable SuperPi 32M and 1M: Use this tool to check for somewhat stability. http://www.sevenforums.com/bsod-help-support/136957-hypertransport-amd-phenom-ii-x6-1075t-causing-bsods.html

And finally, the guide wraps up with several subsections to assist you if you run into trouble. Still works today. :thup:Sinsational 11-23-2011 10:18:20 PM (UTC)xXSebaSXxThat would be one way to go at it. You should know how high you will want to push the voltage, but a reasonable guideline is to not go beyond 1.55V on air cooling.

Just remember that Tech Doc #43375 doesn't have any chipset information in it ... ;)Dolk 03-03-2011 06:14:42 PM (UTC)I did take a relook at this the other day Quite. Make sure you have AOD open and CPU-Z open at the same time. Repeat wPrime test, then repeat CPU speed increase until either one of two things happen; either the system becomes unstable due to lack of voltage, or the CPU will get too luigis replied Feb 1, 2017 at 10:10 AM Windows 7 shutting down and...

CPU-Z will be used as an accurate tool to show what speed your CPU is at, and what Voltage it is at as AOD is not 100% reliable with this. From what I have learned, the HTT likes to stay with the CPU-NB up to 2800 - 3000 MHz. You are going to need Prime95 or a similar tool for this next part. Thanks again.Seebs 11-23-2011 02:55:24 AM (UTC)Sinsationaltheoretically speaking (based on this info) if I want my 1100t to 4.0ghz.

I will use the 940BE in these two examples. Helpful Information - Benchmarking and Stress Testing Tools Depending on whether you want a stable computer, or just benchmark it before it dies, you need the tools to do it. This can be turned on or off. Currently using a 700w XtremeGear power supply.

The Thuban is much more gentler, and allows higher clocked cores without the need for high voltages. http://newwikipost.org/topic/9SajqZiaDy4dvDbHsslxl7xlAkwC0MV6/Motherboard-Processor-causing-BSODs.html You should first try increasing the voltage before increasing the frequency. In no time, you should be able to go from 0% - 29% using your stock cooler and thermal paste. Short URL to this thread: https://techguy.org/973948 Log in with Facebook Log in with Twitter Log in with Google Your name or email address: Do you already have an account?

A Detailed Step by Step Guide to [email protected] Under Linux Step-by-Step: How to Build a Cheap and Quiet AMD Dually AMD Phenom II x4 980 Black Edition Review AMD Phenom II his comment is here First thing is first, for all CPUs: find your walls. I would update it, do the optimized setting then see if it is stable like that. flavallee replied Feb 1, 2017 at 10:06 AM Make Four Words cwwozniak replied Feb 1, 2017 at 9:57 AM Computer Has Been Blocked VJC replied Feb 1, 2017 at 9:48 AM

It often creates a much more stable environment if you do this. Sooner or later you will run into this wall and you will not be able to break it down. The first thing you can do with your RAM is to continue to keep it at stock or close to stock. this contact form First, just try increasing the multiplier.  This method only works with Phenom II BE chips though.

The RAM ratio will be shown in one of two ways depending on your motherboard maker. Only if you intend to run things at stock then use Turbo Mode. If off, the voltage will be set to the specific voltage that you have set in the BIOS.

Part 2 covers the CPU-NB, and HTT but the main focus is the CPU-NB.

I've updated my USB 3.0, SATA RAID, Audio, LAN, and Chipset drivers. I've run 1.250V on the CPU-NB in the past, but I was pushing the frequency on it past 2700MHz... I would suggest you start with lower volts on the CPU-NB... But for a CPU that has a core speed of 2.8 GHz that is increased to 3.0 GHz either technique will create a faster CPU: by increasing the FSB or the

For beginners, I suggest that you read everything before acting. Now you can go a tweak your timings etc, and recheck for stability.Does your mobo support the unlocked cores?BTW I see your post in other forums.. Order online or Call (800)707-0393 Live chat with a representative My Account Sign In Create an account Shopping Cart 0 Exclusive Series Esports Gaming PCs Gaming Laptops Syber Gaming Weekly Special http://zenproject8reviews.com/amd-phenom/amd-phenom-ii-x6.html Check temperature to make sure that you are within range of Max CPU temperature.

This will tell you how far you can go, and at what temperature you may be running at. Still using 4:1 RAM Ratio we would get these new results: 266 * 4 = 1064 1064 / 1 = 1064 1064 * 2 = 2128 You now have some really fast RAM (in As you continue to increase your CPU speed, make sure to watch the CPU temperature. Introduction To Deneb Deneb was the first Phenom II core released.

The second way will show the four basic DRAM Frequencies. I was having issues with installing Windows 7 and learned that HyperTransport is sometimes the cause of the issue and by turning it from "Auto" in the BIOS settings to "X1" The FSB always has a stock frequency of 200 MHz. Note, that "The Heat Wall" will also appear in places you never would expect.

Choose from the AMD FX, AMD Phenom™ II, AMD Athlon™ II, AMD Sempron™ Processors or AMD A-Series APUs when building your desktop PC. This section is intended for those that do not have a B.E.